Product Specication
HXC13 – High speed CMOS camera for advanced industrial vision applications
High resolution: 1280x1024 pixel CMOS Sensor ▪
up to 1024 gray levels (10bit resolution) ▪
up to 500 full frames/sec ▪
arbitrary region of interest ▪
very high sensitivity ▪
14 µm square pixels ▪
electronic “Freeze Frame” shutter ▪
low blooming ▪
programmable via CameraLink ▪
®
serial interface
asynchronous trigger ▪
small, compact housing ▪
wide power supply range ▪
Dimensions
● HXC13 (11008792)
40
63
63
40
40
33
8 x 12-M4 depth 6
Dimensions
● HXC13-F (11008791)
40
63
63
40
33
40
8 x 12-M4 depth 6
Safety
Further Information
For further information on our products visit www.baumer.com
For technical issues, please contact our technical support:
© Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed matter not guaranteed.
Subject to change without notice. Printed in Germany 04/12. V1.1 11037740
FCC – Class B device
No t e : This equipment has been tested and found to
comply with the limits for a Class B digital device, pursu-
ant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interfer-
ence in a residential environment. This equipment gener-
ates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructios,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occure in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off an
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna. ▪
Increase the separation between the equipment and the ▪
receiver.
Connect the equipment into an outlet on a circuit different ▪
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician ▪
for help.
Conformity:
CE, FCC Part 15 Class B, RoHS
Safety Precautions
Notice
See user´s Guide for the comple-
te safety instructions!
Protect the sensor from dirt and ▪
moisture.
Never open the camera housing. ▪
Avoid camera contamination by ▪
foreign objects.
Environmental requirements:
Storage temp. -10°C ... +70°C
Operating temp. +5°C ... +50°C
Housing temp. max. +50°C
Humidity 10 % ... 90 %
Non-condensing
Quick Start Guide
HXC13 - Digital High Speed Camera
Installation
Installation using
Camera Link
®
BASE:
Connect the camera using ▪
an appropriate cable to the
framegrabber board on your
PC using the lower mdr-26
jack on the camera side
If required, connect a strobe ▪
to the HIROSE connector
Connect the camera to ▪
power supply
Installation using
Camera Link
®
MEDIUM /
FULL:
Connect the camera using ▪
two appropriate cables to
the framegrabber board on
your PC (this configuration
requires the BASE and the
FULL Camera Link
®
line)
If required, connect a strobe ▪
to the HIROSE connector
Connect the camera to ▪
power supply
Installation sample
1 - Framegrabber board; 2 - Camera Link
®
cable; 3 - Cable for strobe; 4 - Power cable
Installation sample
1 - Framegrabber board; 2 - Camera Link
®
cable; 3 - Cable for strobe; 4 - Power cable
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals